BandaAncha

  • 🔍 en 📰 artículos ⏎
  • 🔍 en 💬 foros ⏎
  • 🔍 en 👇 este 💬 foro ⏎
  • 🔍 en 👇 este 💬 tema ⏎
Regístrate Regístrate Identifícate Identifícate
Fibra

Configuración router + NAT en Huawei HG8245H para fibra Movistar

tetecohete

Tengo un modem router Huawei HG8245H. He conseguido que funcione el teléfono fijo, pero no consigo que vaya internet.

¿Alguien tiene una de estas funcionando como router principal con O2 o Telefónica?

Josh
1

Edita tu post y detalla mejor qué es lo que necesitas, dónde te falla, qué has probado, etc.

Solospam
2

Tengo un modem Huawei HG8245H. He conseguido que funcione el teléfono fijo,

Tienes el IDONT apropiado, si te funciona el fijo es que la ONT está bien configurada

pero no consigo que vaya internet.

Pon VLAN 6 en tu router, la ONT te sincroniza bien, y presupongo que tienes user::pass correctos de Movistar, el problema lo tienes en la VLAN seguro

tetecohete

Es un router+ONT, he creado la VLAN de internet y la de VoIP, esta última funciona, y tengo fijo, pero no consigo que ande la de internet, queda en estado "conectando" indefinidamente y da un error de ppoe dialing. Si alguien tuviste una funcionando y me pudiese echar una mano lo agradecería. La ONT funciona porque si borro todo menos la idont y pongo detrás un router de telefónica le da servicio

🗨️ 3
vukits

te falta modelo de router neutro

🗨️ 2
tetecohete

No hay router neutro, esta ONT tiene router integrado, con wifi, no necesitas nada mas

🗨️ 1
vukits

Tengo un modem Huawei HG8245H

para futuros posts, cuando dices 'modem' significa un aparato que no hace NAT.

pega por favor pantallazos de cómo has configurado la parte WAN

BocaDePez

Siento el error.captura-pantalla-2021-10-22-170922.webpcaptura-pantalla-2021-10-22-171039.webpcaptura-pantalla-2021-10-22-171118.webp

🗨️ 13
tetecohete

¿Alguien podría mirarlo y echarme una mano?

🗨️ 12
vukits

No veo que esté mal configurado.

Por si acaso, revisa aqui la tabla de VLAN y contraseñas

¿Has probado a levantar sólo la conexión a internet?

De todas amneras, ¿qué error te sale en el log del router? (Ponlo a nivel debug)

lamanonegra
1

El log

Manufacturer:Huawei Technologies Co., Ltd;

ProductClass:EG8145V5;

SerialNumber:00F2021019155635;

IP:192.168.18.1;

HWVer:159D.A;

SWVer:V5R019C00S100;

1981-01-01 00:15:59 [Debug][Debug-Log] static:[dhcp6s] terminal device mac[00:19:e0:68:17:0a]

1981-01-01 00:16:15 [Debug][Debug-Log] static:[dhcp6s] terminal device mac[00:19:e0:68:17:0a]

1981-01-01 00:16:35 [Debug][Debug-Log] static:[dhcpd]receive Discover, xid[f6faa28b], mac[00:19:e0:68:17:0a], requestip[192.168.18.2], option60[MSFT 5.0]

1981-01-01 00:16:35 [Critical][Debug-Log] static:[dhcpd]xid[f6faa28b] choose [main] address pool

1981-01-01 00:16:37 [Debug][Debug-Log] static:[dhcpd]send Ack, xid[f6faa28b], mac[00:19:e0:68:17:0a], request serverip[192.168.18.1], yourip[192.168.18.2], dns1[80.58.61.210], dns2[80.58.61.250]

1981-01-01 00:16:47 [Debug][Debug-Log] static:[dhcp6s] terminal device mac[00:19:e0:68:17:0a]

1981-01-01 00:17:32 [Debug][Debug-Log] static:ETH Port 3 link status changed to Up,Rate is 100 Mbit/s',Work Mode is Full-duplex

1981-01-01 00:17:46 [Debug][Debug-Log] static:[dhcpd]receive Discover, xid[58e862d2], mac[c0:48:e6:ce:5c:82], option60[udhcpc1.21.1]

1981-01-01 00:17:46 [Critical][Debug-Log] static:[dhcpd]xid[58e862d2] choose [main] address pool

1981-01-01 00:17:47 [Debug][Debug-Log] static:[dhcpd]receive Discover, xid[58e862d2], mac[c0:48:e6:ce:5c:82], option60[udhcpc1.21.1]

1981-01-01 00:17:47 [Critical][Debug-Log] static:[dhcpd]xid[58e862d2] choose [main] address pool

1981-01-01 00:17:47 [Debug][Debug-Log] static:[dhcpd]receive Discover, xid[58e862d2], mac[c0:48:e6:ce:5c:82], option60[udhcpc1.21.1]

1981-01-01 00:17:47 [Critical][Debug-Log] static:[dhcpd]xid[58e862d2] choose [main] address pool

1981-01-01 00:17:47 [Debug][Debug-Log] static:[dhcpd]receive Discover, xid[58e862d2], mac[c0:48:e6:ce:5c:82], option60[udhcpc1.21.1]

1981-01-01 00:17:47 [Critical][Debug-Log] static:[dhcpd]xid[58e862d2] choose [main] address pool

1981-01-01 00:17:48 [Debug][Debug-Log] static:[dhcpd]receive Discover, xid[58e862d2], mac[c0:48:e6:ce:5c:82], option60[udhcpc1.21.1]

1981-01-01 00:17:48 [Critical][Debug-Log] static:[dhcpd]xid[58e862d2] choose [main] address pool

1981-01-01 00:17:49 [Debug][Debug-Log] static:[dhcpd]send Ack, xid[58e862d2], mac[c0:48:e6:ce:5c:82], request serverip[192.168.18.1], yourip[192.168.18.4], dns1[80.58.61.210], dns2[80.58.61.250]

1981-01-01 00:18:27 [Debug][Debug-Log] static:[dhcp6s] terminal device mac[b4:2e:99:73:c0:aa]

1981-01-01 00:18:27 [Debug][Debug-Log] static:[dhcp6s] terminal device mac[b4:2e:99:73:c0:aa]

1981-01-01 00:18:28 [Debug][Debug-Log] static:[dhcp6s] terminal device mac[b4:2e:99:73:c0:aa]

1981-01-01 00:18:29 [Debug][Debug-Log] static:[dhcp6s] terminal device mac[b4:2e:99:73:c0:aa]

1981-01-01 00:18:31 [Debug][Debug-Log] static:[dhcp6s] terminal device mac[b4:2e:99:73:c0:aa]

1981-01-01 00:18:35 [Debug][Debug-Log] static:[dhcp6s] terminal device mac[b4:2e:99:73:c0:aa]

1981-01-01 00:18:43 [Debug][Debug-Log] static:[dhcp6s] terminal device mac[b4:2e:99:73:c0:aa]

1981-01-01 00:18:59 [Debug][Debug-Log] static:[dhcp6s] terminal device mac[b4:2e:99:73:c0:aa]

1981-01-01 00:19:31 [Debug][Debug-Log] static:[dhcp6s] terminal device mac[b4:2e:99:73:c0:aa]

1981-01-01 00:00:11 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up pre, WAN Index=0x30000001.

1981-01-01 00:00:11 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv6 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state down, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up pre, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:13 [Informational][Debug-Log] static:[pppoec] start PPPoE client! pppunit[257],mru[1492],nasName[wan1],ipv4Enable[1],ipv6Enable[0]

1981-01-01 00:00:13 [Debug][Debug-Log] static:[pppoec]WAN[wan1] send PADI, smac[a8:f5:ac:1f:d3:c9], dmac[ff:ff:ff:ff:ff:ff]

1981-01-01 00:00:17 [Debug][Debug-Log] static:ETH Port 3 link status changed to Up,Rate is 100 Mbit/s',Work Mode is Full-duplex

1981-01-01 00:00:24 [Debug][Debug-Log] static:[L2M] pon state change process. Status=up.

1981-01-01 00:00:30 [Debug][Debug-Log] static:[ra]send ra notify message! m[1],o[1],lanPrefix[fda8:f5ac:1fd3:c800::],mtu[1492],gateway[fe80::1]

1981-01-01 00:01:42 [Debug][Debug-Log] static:[L2M] pon state change process. Status=down.

1981-01-01 00:01:51 [Debug][Debug-Log] static:[L2M] pon state change process. Status=up.

1981-01-01 00:25:10 [Error][Debug-Log] static:[dhcpd]request packet has no lease,send nak! xid[58e862d2] mac[c0:48:e6:ce:5c:82] IP[0]

1981-01-01 00:25:13 [Debug][Debug-Log] static:[dhcpd]receive Discover, xid[58e862d2], mac[c0:48:e6:ce:5c:82], option60[udhcpc1.21.1]

1981-01-01 00:25:13 [Critical][Debug-Log] static:[dhcpd]xid[58e862d2] choose [main] address pool

1981-01-01 00:25:13 [Critical][Debug-Log] static:[dhcpd]receive arp reply from mac[c0:48:e6:ce:5c:82], IP[192.168.18.4]

1981-01-01 00:25:13 [Debug][Debug-Log] static:[dhcpd]receive Discover, xid[58e862d2], mac[c0:48:e6:ce:5c:82], option60[udhcpc1.21.1]

1981-01-01 00:25:13 [Critical][Debug-Log] static:[dhcpd]xid[58e862d2] choose [main] address pool

1981-01-01 00:25:13 [Critical][Debug-Log] static:[dhcpd]receive arp reply from mac[c0:48:e6:ce:5c:82], IP[192.168.18.4]

1981-01-01 00:25:13 [Debug][Debug-Log] static:[dhcpd]receive Discover, xid[58e862d2], mac[c0:48:e6:ce:5c:82], option60[udhcpc1.21.1]

1981-01-01 00:25:13 [Critical][Debug-Log] static:[dhcpd]xid[58e862d2] choose [main] address pool

1981-01-01 00:25:13 [Critical][Debug-Log] static:[dhcpd]receive arp reply from mac[c0:48:e6:ce:5c:82], IP[192.168.18.4]

1981-01-01 00:25:14 [Debug][Debug-Log] static:[dhcpd]receive Discover, xid[58e862d2], mac[c0:48:e6:ce:5c:82], option60[udhcpc1.21.1]

1981-01-01 00:25:14 [Critical][Debug-Log] static:[dhcpd]xid[58e862d2] choose [main] address pool

1981-01-01 00:25:14 [Critical][Debug-Log] static:[dhcpd]receive arp reply from mac[c0:48:e6:ce:5c:82], IP[192.168.18.4]

1981-01-01 00:25:15 [Debug][Debug-Log] static:[dhcpd]send Ack, xid[58e862d2], mac[c0:48:e6:ce:5c:82], request serverip[192.168.18.1], yourip[192.168.18.5], dns1[80.58.61.210], dns2[80.58.61.250]

1981-01-01 00:33:28 [Error][Debug-Log] static:[dhcpd]request packet has no lease,send nak! xid[3e6d30dc] mac[e8:5a:8b:38:64:3c] IP[c0a81203]

1981-01-01 00:33:28 [Debug][Debug-Log] static:[dhcpd]receive Discover, xid[36229dd0], mac[e8:5a:8b:38:64:3c], option60[Android-DHCP-11]

1981-01-01 00:33:28 [Critical][Debug-Log] static:[dhcpd]xid[36229dd0] choose [main] address pool

1981-01-01 00:33:29 [Debug][Debug-Log] static:[dhcpd]receive Discover, xid[36229dd0], mac[e8:5a:8b:38:64:3c], option60[Android-DHCP-11]

1981-01-01 00:33:29 [Critical][Debug-Log] static:[dhcpd]xid[36229dd0] choose [main] address pool

1981-01-01 00:33:30 [Debug][Debug-Log] static:[dhcpd]send Ack, xid[36229dd0], mac[e8:5a:8b:38:64:3c], request serverip[192.168.18.1], yourip[192.168.18.3], dns1[80.58.61.210], dns2[80.58.61.250]

1981-01-01 00:55:16 [Debug][Debug-Log] static:[dhcpd]send Ack, xid[58e862d2], mac[c0:48:e6:ce:5c:82], request serverip[192.168.18.1], clientip[192.168.18.5], yourip[192.168.18.5], dns1[80.58.61.210], dns2[80.58.61.250]

1981-01-01 01:00:14 [Debug][Debug-Log] static:[pppoec]WAN[wan1] send PADI, smac[a8:f5:ac:1f:d3:c9], dmac[ff:ff:ff:ff:ff:ff]

1981-01-01 01:03:32 [Debug][Debug-Log] static:[dhcpd]send Ack, xid[c8bcb5c8], mac[e8:5a:8b:38:64:3c], request serverip[192.168.18.1], clientip[192.168.18.3], yourip[192.168.18.3], dns1[80.58.61.210], dns2[80.58.61.250]

1981-01-01 01:25:16 [Debug][Debug-Log] static:[dhcpd]send Ack, xid[58e862d2], mac[c0:48:e6:ce:5c:82], request serverip[192.168.18.1], clientip[192.168.18.5], yourip[192.168.18.5], dns1[80.58.61.210], dns2[80.58.61.250]

1981-01-01 01:33:33 [Debug][Debug-Log] static:[dhcpd]send Ack, xid[bfd7d8e], mac[e8:5a:8b:38:64:3c], request serverip[192.168.18.1], clientip[192.168.18.3], yourip[192.168.18.3], dns1[80.58.61.210], dns2[80.58.61.250]

1981-01-01 01:55:16 [Debug][Debug-Log] static:[dhcpd]send Ack, xid[58e862d2], mac[c0:48:e6:ce:5c:82], request serverip[192.168.18.1], clientip[192.168.18.5], yourip[192.168.18.5], dns1[80.58.61.210], dns2[80.58.61.250]

1981-01-01 02:00:45 [Debug][Debug-Log] static:[pppoec]WAN[wan1] send PADI, smac[a8:f5:ac:1f:d3:c9], dmac[ff:ff:ff:ff:ff:ff]

1981-01-01 02:03:34 [Debug][Debug-Log] static:[dhcpd]send Ack, xid[d00bde39], mac[e8:5a:8b:38:64:3c], request serverip[192.168.18.1], clientip[192.168.18.3], yourip[192.168.18.3], dns1[80.58.61.210], dns2[80.58.61.250]

1981-01-01 02:20:55 [Debug][Debug-Log] static:[dhcpd]send Ack, xid[4a189c63], mac[e8:5a:8b:38:64:3c], request serverip[192.168.18.1], yourip[192.168.18.3], dns1[80.58.61.210], dns2[80.58.61.250]

1981-01-01 02:25:16 [Debug][Debug-Log] static:[dhcpd]send Ack, xid[58e862d2], mac[c0:48:e6:ce:5c:82], request serverip[192.168.18.1], clientip[192.168.18.5], yourip[192.168.18.5], dns1[80.58.61.210], dns2[80.58.61.250]

1981-01-01 02:29:47 [Critical][Debug-Log] static:[dhcpc]get WAN[wan2] ifindex[38] and Mac Addr[a8:f5:ac:1f:d3:ca] success!

1981-01-01 02:29:47 [Debug][Debug-Log] static:[dhcpc]send Discover, WAN[wan2], xid[d0a8da0b], mac[a8:f5:ac:1f:d3:ca]

1981-01-01 02:30:08 [Debug][Debug-Log] static:[L2M] pon state change process. Status=down.

1981-01-01 02:30:17 [Debug][Debug-Log] static:[L2M] pon state change process. Status=up.

1981-01-01 02:42:53 [Debug][Debug-Log] static:[L2M] pon state change process. Status=down.

1981-01-01 02:43:03 [Debug][Debug-Log] static:[L2M] pon state change process. Status=up.

1981-01-01 02:55:16 [Debug][Debug-Log] static:[dhcpd]send Ack, xid[58e862d2], mac[c0:48:e6:ce:5c:82], request serverip[192.168.18.1], clientip[192.168.18.5], yourip[192.168.18.5], dns1[80.58.61.210], dns2[80.58.61.250]

1981-01-01 03:01:20 [Debug][Debug-Log] static:[pppoec]WAN[wan1] send PADI, smac[a8:f5:ac:1f:d3:c9], dmac[ff:ff:ff:ff:ff:ff]

1981-01-01 03:03:24 [Debug][Debug-Log] static:[L2M] pon state change process. Status=down.

1981-01-01 03:03:34 [Debug][Debug-Log] static:[L2M] pon state change process. Status=up.

1981-01-01 03:03:55 [Debug][Debug-Log] static:[L2M] pon state change process. Status=down.

1981-01-01 03:04:05 [Debug][Debug-Log] static:[L2M] pon state change process. Status=up.

1981-01-01 03:07:21 [Debug][Debug-Log] static:[L2M] pon state change process. Status=down.

1981-01-01 03:07:30 [Debug][Debug-Log] static:[L2M] pon state change process. Status=up.

1981-01-01 03:21:03 [Informational][Debug-Log] static:[pppoec] start PPPoE client! pppunit[257],mru[1492],nasName[wan1],ipv4Enable[1],ipv6Enable[0]

1981-01-01 03:21:03 [Debug][Debug-Log] static:[pppoec]WAN[wan1] send PADI, smac[a8:f5:ac:1f:d3:c9], dmac[ff:ff:ff:ff:ff:ff]

1981-01-01 03:25:16 [Debug][Debug-Log] static:[dhcpd]send Ack, xid[58e862d2], mac[c0:48:e6:ce:5c:82], request serverip[192.168.18.1], clientip[192.168.18.5], yourip[192.168.18.5], dns1[80.58.61.210], dns2[80.58.61.250]

1981-01-01 03:30:05 [Informational][Debug-Log] static:[pppoec] start PPPoE client! pppunit[257],mru[1492],nasName[wan1],ipv4Enable[1],ipv6Enable[0]

1981-01-01 03:30:05 [Debug][Debug-Log] static:[pppoec]WAN[wan1] send PADI, smac[a8:f5:ac:1f:d3:c9], dmac[ff:ff:ff:ff:ff:ff]

1981-01-01 03:36:29 [Debug][Debug-Log] static:[L2M] pon state change process. Status=down.

1981-01-01 00:00:11 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up pre, WAN Index=0x30000001.

1981-01-01 00:00:11 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv6 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state down, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up pre, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:13 [Informational][Debug-Log] static:[pppoec] start PPPoE client! pppunit[257],mru[1492],nasName[wan1],ipv4Enable[1],ipv6Enable[0]

1981-01-01 00:00:14 [Debug][Debug-Log] static:[pppoec]WAN[wan1] send PADI, smac[a8:f5:ac:1f:d3:c9], dmac[ff:ff:ff:ff:ff:ff]

1981-01-01 00:00:19 [Debug][Debug-Log] static:ETH Port 1 link status changed to Up,Rate is 1000 Mbit/s',Work Mode is Full-duplex

1981-01-01 00:00:10 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up pre, WAN Index=0x30000001.

1981-01-01 00:00:10 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv6 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state down, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up pre, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:13 [Informational][Debug-Log] static:[pppoec] start PPPoE client! pppunit[257],mru[1492],nasName[wan1],ipv4Enable[1],ipv6Enable[0]

1981-01-01 00:00:13 [Debug][Debug-Log] static:[pppoec]WAN[wan1] send PADI, smac[a8:f5:ac:1f:d3:c9], dmac[ff:ff:ff:ff:ff:ff]

1981-01-01 00:00:11 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up pre, WAN Index=0x30000001.

1981-01-01 00:00:11 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv6 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state down, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up pre, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:13 [Informational][Debug-Log] static:[pppoec] start PPPoE client! pppunit[257],mru[1492],nasName[wan1],ipv4Enable[1],ipv6Enable[0]

1981-01-01 00:00:13 [Debug][Debug-Log] static:[pppoec]WAN[wan1] send PADI, smac[a8:f5:ac:1f:d3:c9], dmac[ff:ff:ff:ff:ff:ff]

1981-01-01 00:00:19 [Debug][Debug-Log] static:ETH Port 1 link status changed to Up,Rate is 100 Mbit/s',Work Mode is Full-duplex

1981-01-01 00:00:24 [Debug][Debug-Log] static:ETH Port 1 link status changed to Down,Rate is –,Work Mode is –

1981-01-01 00:00:27 [Debug][Debug-Log] static:ETH Port 1 link status changed to Up,Rate is 1000 Mbit/s',Work Mode is Full-duplex

1981-01-01 00:05:50 [Informational][Debug-Log] static:[pppoec] start PPPoE client! pppunit[257],mru[1492],nasName[wan1],ipv4Enable[1],ipv6Enable[0]

1981-01-01 00:05:50 [Debug][Debug-Log] static:[pppoec]WAN[wan1] send PADI, smac[a8:f5:ac:1f:d3:c9], dmac[ff:ff:ff:ff:ff:ff]

1981-01-01 00:08:42 [Debug][Debug-Log] static:[ra]send ra notify message! m[1],o[1],lanPrefix[fda8:f5ac:1fd3:c800::],mtu[1492],gateway[fe80::1]

1981-01-01 00:10:02 [Debug][Debug-Log] static:[dhcpd]receive Discover, xid[c8a3d7d0], mac[e8:5a:8b:38:64:3c], option60[Android-DHCP-11]

1981-01-01 00:10:02 [Critical][Debug-Log] static:[dhcpd]xid[c8a3d7d0] choose [main] address pool

1981-01-01 00:10:03 [Debug][Debug-Log] static:[dhcpd]receive Discover, xid[c8a3d7d0], mac[e8:5a:8b:38:64:3c], option60[Android-DHCP-11]

1981-01-01 00:10:03 [Critical][Debug-Log] static:[dhcpd]xid[c8a3d7d0] choose [main] address pool

1981-01-01 00:10:04 [Debug][Debug-Log] static:[dhcpd]send Ack, xid[c8a3d7d0], mac[e8:5a:8b:38:64:3c], request serverip[192.168.18.1], yourip[192.168.18.3], dns1[80.58.61.250], dns2[80.58.61.254]

1981-01-01 00:17:13 [Informational][Debug-Log] static:[pppoec] start PPPoE client! pppunit[257],mru[1500],nasName[wan1],ipv4Enable[1],ipv6Enable[1]

1981-01-01 00:17:14 [Debug][Debug-Log] static:[pppoec]WAN[wan1] send PADI, smac[a8:f5:ac:1f:d3:c9], dmac[ff:ff:ff:ff:ff:ff]

1981-01-01 00:17:14 [Informational][Debug-Log] static:[dhcp6s]DHCP server configure file DNS[fe80::1]

1981-01-01 00:00:11 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up pre, WAN Index=0x30000001.

1981-01-01 00:00:11 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv6 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state down, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up pre, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:13 [Informational][Debug-Log] static:[pppoec] start PPPoE client! pppunit[257],mru[1500],nasName[wan1],ipv4Enable[1],ipv6Enable[1]

1981-01-01 00:00:13 [Debug][Debug-Log] static:[pppoec]WAN[wan1] send PADI, smac[a8:f5:ac:1f:d3:c9], dmac[ff:ff:ff:ff:ff:ff]

1981-01-01 00:00:14 [Informational][Debug-Log] static:[dhcp6s]DHCP server configure file DNS[fe80::1]

1981-01-01 00:00:18 [Debug][Debug-Log] static:ETH Port 1 link status changed to Up,Rate is 1000 Mbit/s',Work Mode is Full-duplex

1981-01-01 00:00:10 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up pre, WAN Index=0x30000001.

1981-01-01 00:00:10 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv6 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state down, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up pre, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:13 [Informational][Debug-Log] static:[pppoec] start PPPoE client! pppunit[257],mru[1500],nasName[wan1],ipv4Enable[1],ipv6Enable[1]

1981-01-01 00:00:13 [Debug][Debug-Log] static:[pppoec]WAN[wan1] send PADI, smac[a8:f5:ac:1f:d3:c9], dmac[ff:ff:ff:ff:ff:ff]

1981-01-01 00:00:14 [Informational][Debug-Log] static:[dhcp6s]DHCP server configure file DNS[fe80::1]

1981-01-01 00:00:15 [Informational][Debug-Log] static:[dhcp6s]DHCP server configure file DNS[fe80::1]

1981-01-01 00:00:15 [Informational][Debug-Log] static:[dhcp6s]DHCP server configure file DNS[fe80::1]

1981-01-01 00:00:27 [Debug][Debug-Log] static:[L2M] pon state change process. Status=up.

1981-01-01 00:00:30 [Debug][Debug-Log] static:[ra]send ra notify message! m[1],o[1],lanPrefix[fda8:f5ac:1fd3:c800::],mtu[1492],gateway[fe80::1]

1981-01-01 00:00:49 [Error][Debug-Log] static:[dhcpd]request packet has no lease,send nak! xid[882646be] mac[e8:5a:8b:38:64:3c] IP[c0a81203]

1981-01-01 00:00:49 [Debug][Debug-Log] static:[dhcpd]receive Discover, xid[c701f490], mac[e8:5a:8b:38:64:3c], option60[Android-DHCP-11]

1981-01-01 00:00:49 [Critical][Debug-Log] static:[dhcpd]xid[c701f490] choose [main] address pool

1981-01-01 00:00:50 [Debug][Debug-Log] static:[dhcpd]receive Discover, xid[c701f490], mac[e8:5a:8b:38:64:3c], option60[Android-DHCP-11]

1981-01-01 00:00:50 [Critical][Debug-Log] static:[dhcpd]xid[c701f490] choose [main] address pool

1981-01-01 00:00:51 [Debug][Debug-Log] static:[dhcpd]send Ack, xid[c701f490], mac[e8:5a:8b:38:64:3c], request serverip[192.168.18.1], yourip[192.168.18.3], dns1[80.58.61.250], dns2[80.58.61.254]

1981-01-01 00:02:27 [Debug][Debug-Log] static:ETH Port 1 link status changed to Up,Rate is 100 Mbit/s',Work Mode is Full-duplex

1981-01-01 00:05:44 [Informational][Debug-Log] static:[pppoec] start PPPoE client! pppunit[257],mru[1500],nasName[wan1],ipv4Enable[1],ipv6Enable[1]

1981-01-01 00:05:44 [Debug][Debug-Log] static:[pppoec]WAN[wan1] send PADI, smac[a8:f5:ac:1f:d3:c9], dmac[ff:ff:ff:ff:ff:ff]

1981-01-01 00:09:11 [Debug][Debug-Log] static:[L2M] pon state change process. Status=down.

1981-01-01 00:09:21 [Debug][Debug-Log] static:[L2M] pon state change process. Status=up.

1981-01-01 00:10:41 [Debug][Debug-Log] static:[L2M] pon state change process. Status=down.

1981-01-01 00:10:51 [Debug][Debug-Log] static:[L2M] pon state change process. Status=up.

1981-01-01 00:12:54 [Debug][Debug-Log] static:[L2M] pon state change process. Status=down.

1981-01-01 00:13:04 [Debug][Debug-Log] static:[L2M] pon state change process. Status=up.

1981-01-01 00:19:39 [Debug][Debug-Log] static:[L2M] pon state change process. Status=down.

1981-01-01 00:19:49 [Debug][Debug-Log] static:[L2M] pon state change process. Status=up.

1981-01-01 00:22:31 [Debug][Debug-Log] static:[L2M] pon state change process. Status=down.

1981-01-01 00:22:41 [Debug][Debug-Log] static:[L2M] pon state change process. Status=up.

1981-01-01 00:29:46 [Debug][Debug-Log] static:[L2M] pon state change process. Status=down.

1981-01-01 00:29:55 [Debug][Debug-Log] static:[L2M] pon state change process. Status=up.

1981-01-01 01:05:52 [Debug][Debug-Log] static:[pppoec]WAN[wan1] send PADI, smac[a8:f5:ac:1f:d3:c9], dmac[ff:ff:ff:ff:ff:ff]

1981-01-01 00:00:10 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up pre, WAN Index=0x30000001.

1981-01-01 00:00:10 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv6 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state down, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up pre, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:13 [Informational][Debug-Log] static:[pppoec] start PPPoE client! pppunit[257],mru[1492],nasName[wan1],ipv4Enable[1],ipv6Enable[0]

1981-01-01 00:00:13 [Debug][Debug-Log] static:[pppoec]WAN[wan1] send PADI, smac[a8:f5:ac:1f:d3:c9], dmac[ff:ff:ff:ff:ff:ff]

1981-01-01 00:00:16 [Debug][Debug-Log] static:ETH Port 1 link status changed to Up,Rate is 100 Mbit/s',Work Mode is Full-duplex

1981-01-01 00:00:25 [Debug][Debug-Log] static:[L2M] pon state change process. Status=up.

1981-01-01 00:00:30 [Debug][Debug-Log] static:[ra]send ra notify message! m[1],o[1],lanPrefix[fda8:f5ac:1fd3:c800::],mtu[1492],gateway[fe80::1]

1981-01-01 00:01:05 [Debug][Debug-Log] static:[dhcpd]receive Discover, xid[f3de2a11], mac[e8:5a:8b:38:64:3c], option60[Android-DHCP-11]

1981-01-01 00:01:05 [Critical][Debug-Log] static:[dhcpd]xid[f3de2a11] choose [main] address pool

1981-01-01 00:01:06 [Debug][Debug-Log] static:[dhcpd]receive Discover, xid[f3de2a11], mac[e8:5a:8b:38:64:3c], option60[Android-DHCP-11]

1981-01-01 00:01:06 [Critical][Debug-Log] static:[dhcpd]xid[f3de2a11] choose [main] address pool

1981-01-01 00:01:07 [Debug][Debug-Log] static:[dhcpd]send Ack, xid[f3de2a11], mac[e8:5a:8b:38:64:3c], request serverip[192.168.18.1], yourip[192.168.18.3], dns1[80.58.61.250], dns2[80.58.61.254]

1981-01-01 00:00:10 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up pre, WAN Index=0x30000001.

1981-01-01 00:00:10 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv6 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state down, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up pre, WAN Index=0x30000001.

1981-01-01 00:00:12 [Debug][Debug-Log] static:[WAN_MNGT] IPv4 if set WAN state up, WAN Index=0x30000001.

1981-01-01 00:00:13 [Informational][Debug-Log] static:[pppoec] start PPPoE client! pppunit[257],mru[1492],nasName[wan1],ipv4Enable[1],ipv6Enable[0]

1981-01-01 00:00:13 [Debug][Debug-Log] static:[pppoec]WAN[wan1] send PADI, smac[a8:f5:ac:1f:d3:c9], dmac[ff:ff:ff:ff:ff:ff]

1981-01-01 00:00:17 [Debug][Debug-Log] static:ETH Port 1 link status changed to Up,Rate is 100 Mbit/s',Work Mode is Full-duplex

1981-01-01 00:00:30 [Debug][Debug-Log] static:[ra]send ra notify message! m[1],o[1],lanPrefix[fda8:f5ac:1fd3:c800::],mtu[1492],gateway[fe80::1]

1981-01-01 00:02:16 [Alert][Debug-Log] dynamic:Load memu from the directory [/html/menu/MenuSmartAbroad.xml].

🗨️ 9
vukits
vukits
🗨️ 2
tetecohete
tetecohete
🗨️ 1
vukits
vukits
tetecohete
tetecohete
🗨️ 5
vukits
vukits
🗨️ 4
tetecohete
tetecohete
🗨️ 3
vukits
vukits
apocalypse
apocalypse
🗨️ 1
tetecohete

La dos primeras caapturas con la VLAN 6/1 desactivada, cuando la habilito se va todo al traste

tetecohete

Este es el error

🗨️ 1
vukits

¿has probado los varios 'Dialing Method' que hay?

vukits

¿Me puedes confirmar de que no eres cliente empresa / PYME , y que no tienes contratada IP fija?

vukits

Huawei no facilita el firmware

@tetecohete

buscate la vida, compi :P …

hay ficheros de actualización por ahí… sólo toca buscar (no te paso ninguno, porque el fichero equivocado puede romper el router ;) )

BocaDePez

Particular, y Huawei no facilita el firmware

BocaDePez

Vukits, si tienes alguno te lo agradezco y me la juego, porque yo no lo encuentro por el mundo dios

BocaDePez

O algún compi que pueda y quiera echar una nano

BocaDePez

Al final me he cabreado y he cambiado a Orange, y ¡oh! sorpresa, he configurado la ONT eg8145v5 y ha salido andando a la primera, solo me queda ver si funciona el telefono cuando me lo activen. Gracias a todos.

🗨️ 1
vukits

solo me queda ver si funciona el telefono cuando me lo activen

madre mía, compi.,… te metes en camisas de once varas… ni de coña te van a activar el servicio de voz en un aparato por el que no tienen perfil de telecarga.

¡Deberías haberte quedado en Movistar/O2, que sí que te dejan usar tus propios équipos para Voz!